Circuit Diagram

                   CIRCUIT DIAGRAM

Combinational circuit is a circuit in which we combine the different gates in the circuit, for example encoder, decoder, multiplexer and demultiplexer. Some of the characteristics of combinational circuits are following −

• The output of combinational circuit at any instant of time, depends only on the levels present at input terminals.
• The combinational circuit do not use any memory. The previous state of input does not have any effect on the present state of the circuit.
• A combinational circuit can have an n number of inputs and m number of outputs.
• BLOCK DIAGRAM
• 
  
• 
  

  

  TYPES OF COMBINATIONAL CUIRCUIT :
  

1. Half Adder
2. Full Adder
3. Half Subtractor
4. Full Subtractor
5. Multiplexor
6. De-multiplexor
7. Encoder
8. Decoder
9. N-Bit parallel Adder
10. N-Bit Parallel Subtractor

HALF ADDER:Half adder is a combinational logic circuit with two inputs and two outputs. The half adder circuit is designed to add two single bit binary number A and B. It is the basic building block for addition of two single bit numbers. This circuit has two outputs carry and sum.

BLOCK DIAGRAM:

                         

TRUTH TABLE:

                                   

CUIRCUIT DAIGRAM:

FULL ADDER:Full adder is developed to overcome the drawback of Half Adder circuit. It can add two one-bit numbers A and B, and carry c. The full adder is a three input and two output combinational circuit.

BLOCK DIAGRAM:

TRUTH TABLE:

CIRCUIT DIAGRAM:

N-Bit Parallel Adder:

he Full Adder is capable of adding only two single digit binary number along with a carry input. But in practical we need to add binary numbers which are much longer than just one bit. To add two n-bit binary numbers we need to use the n-bit parallel adder. It uses a number of full adders in cascade. The carry output of the previous full adder is connected to carry input of the next full adder.

Block diagram:

N-Bit Parallel Subtractor

The subtraction can be carried out by taking the 1's or 2's complement of the number to be subtracted. For example we can perform the subtraction (A-B) by adding either 1's or 2's complement of B to A. That means we can use a binary adder to perform the binary subtraction.

Block diagram:

Half Subtractors:

Half subtractor is a combination circuit with two inputs and two outputs (difference and borrow). It produces the difference between the two binary bits at the input and also produces an output (Borrow) to indicate if a 1 has been borrowed. In the subtraction (A-B), A is called as Minuend bit and B is called as Subtrahend bit.

Truth Table

Circuit Diagram

Full Subtractors

The disadvantage of a half subtractor is overcome by full subtractor. The full subtractor is a combinational circuit with three inputs A,B,C and two output D and C'. A is the 'minuend', B is 'subtrahend', C is the 'borrow' produced by the previous stage, D is the difference output and C' is the borrow output.

Truth Table

Circuit Diagram

Multiplexers

Multiplexer is a special type of combinational circuit. There are n-data inputs, one output and m select inputs with 2m = n. It is a digital circuit which selects one of the n data inputs and routes it to the output. The selection of one of the n inputs is done by the selected inputs. Depending on the digital code applied at the selected inputs, one out of n data sources is selected and transmitted to the single output Y. E is called the strobe or enable input which is useful for the cascading. It is generally an active low terminal that means it will perform the required operation when it is low.

Block diagram

Multiplexers come in multiple variations

• 2 : 1 multiplexer
• 4 : 1 multiplexer
• 16 : 1 multiplexer
• 32 : 1 multiplexer

Block Diagram

Truth Table

Demultiplexers

A demultiplexer performs the reverse operation of a multiplexer i.e. it receives one input and distributes it over several outputs. It has only one input, n outputs, m select input. At a time only one output line is selected by the select lines and the input is transmitted to the selected output line. A de-multiplexer is equivalent to a single pole multiple way switch as shown in fig.

Demultiplexers comes in multiple variations.

• 1 : 2 demultiplexer
• 1 : 4 demultiplexer
• 1 : 16 demultiplexer
• 1 : 32 demultiplexer

Block diagram

Truth Table

Decoder

A decoder is a combinational circuit. It has n input and to a maximum m = 2n outputs. Decoder is identical to a demultiplexer without any data input. It performs operations which are exactly opposite to those of an encoder.

Block diagram

Examples of Decoders are following.

• Code converters
• BCD to seven segment decoders
• Nixie tube decoders
• Relay actuator

2 to 4 Line Decoder

The block diagram of 2 to 4 line decoder is shown in the fig. A and B are the two inputs where D through D are the four outputs. Truth table explains the operations of a decoder. It shows that each output is 1 for only a specific combination of inputs.

Block diagram

Truth Table

Logic Circuit

Encoder

Encoder is a combinational circuit which is designed to perform the inverse operation of the decoder. An encoder has n number of input lines and m number of output lines. An encoder produces an m bit binary code corresponding to the digital input number. The encoder accepts an n input digital word and converts it into an m bit another digital word.

Block diagram

Examples of Encoders are following.

• Priority encoders
• Decimal to BCD encoder
• Octal to binary encoder
• Hexadecimal to binary encoder

Priority Encoder

This is a special type of encoder. Priority is given to the input lines. If two or more input line are 1 at the same time, then the input line with highest priority will be considered. There are four input D₀, D₁, D₂, D₃ and two output Y₀, Y₁. Out of the four input D₃ has the highest priority and D₀ has the lowest priority. That means if D₃ = 1 then Y₁ Y₁ = 11 irrespective of the other inputs. Similarly if D₃ = 0 and D₂ = 1 then Y₁ Y₀ = 10 irrespective of the other inputs.

Block diagram

Truth Table

Logic Circuit